MOXA NPort 5650
8/16-port RS-232/422/485 Rackmount Serial Device Servers
- 8 or 16 serial ports supporting RS-232/422/485
- Standard 19-inch rackmount size
- 10/100M auto-sensing Ethernet
- Easy IP address configuration with LCD panel (excluding wide temperature models)
- Configure via Telnet/Web/Windows utility
- Socket modes: TCP server/TCP client/UDP/Real COM
- SNMP MIB-II for network management
- Universal high-voltage range: 100 to 240 VAC or 88 to 300 VDC
- Popular low-voltage ranges: ±48 VDC (20 to 72 VDC, -20 to -72 VDC)
Der NPort® 5650-Rack-Geräteserver kann komfortabel und transparent bis zu 16 serielle Geräte mit einem Ethernet verbinden, sodass Sie Ihre seriellen Geräte mit einer einfachen Basiskonfiguration vernetzen können. Die Datenübertragung zwischen den seriellen und Ethernet-Schnittstellen erfolgt bidirektional. Mithilfe von NPort® Geräteservern schützen Sie nicht nur Ihre aktuelle Hardwareinvestition, sondern ermöglichen außerdem die zukünftige Netzwerkerweiterung. Sie können das Management ihrer seriellen Geräte zentralisieren und Managementserver über das Netzwerk verteilen.
With the NPort® 5600 rackmount series, you not only protect your current hardware investment, but also allow for future network expansion by centralizing the management of your serial devices and distributing management hosts over the network.
Network Readiness for up to 16 Serial Devices
Only basic configuration is needed with the NPort® 5600 to connect up to 16 serial devices to an Ethernet network.
19-inch Rackmount Device Server
NPort® 5600 device servers come with Tx/Rx LEDs for the serial ports on the front panel, and 8 or 16 RJ45 serial port connectors on the rear panel. This makes the NPort® 5600 device servers suitable for standard 19-inch rack mounting, allowing you to simplify operational, maintenance, and administrative tasks.
Real COM/TTY Ports
Real COM/TTY drivers are provided to make the serial ports on the NPort® 5600 recognizable as Real COM ports by Windows, or Real TTY ports by Linux. In addition to supporting basic data transmission and reception, the NPort® drivers also support the RTS, CTS, DTR, DSR, and DCD control signals.
LED Indicators to Ease Your Maintenance Tasks
The System LED, serial Tx/Rx LEDs, and Ethernet LEDs (located on the RJ45 connector) provide a great tool for basic maintenance tasks and help engineers analyze problems in the field. The LEDs not only indicate current system and network status, but also help field engineers monitor the status of attached serial devices.
Adjustable Termination and Pull High/Low Resistors
When using termination resistors to prevent serial signal reflection, it is important to set the pull high/low resistors correctly so that the electrical signal is not corrupted. Since no set of resistor values is universally compatible for all environments, the NPort® 5650-8/16 has DIP switches on the bottom panel for setting the termination and pull high/low resistor values.
Network Readiness for up to 16 Serial Devices
Only basic configuration is needed with the NPort® 5600 to connect up to 16 serial devices to an Ethernet network.
19-inch Rackmount Device Server
NPort® 5600 device servers come with Tx/Rx LEDs for the serial ports on the front panel, and 8 or 16 RJ45 serial port connectors on the rear panel. This makes the NPort® 5600 device servers suitable for standard 19-inch rack mounting, allowing you to simplify operational, maintenance, and administrative tasks.
Real COM/TTY Ports
Real COM/TTY drivers are provided to make the serial ports on the NPort® 5600 recognizable as Real COM ports by Windows, or Real TTY ports by Linux. In addition to supporting basic data transmission and reception, the NPort® drivers also support the RTS, CTS, DTR, DSR, and DCD control signals.
LED Indicators to Ease Your Maintenance Tasks
The System LED, serial Tx/Rx LEDs, and Ethernet LEDs (located on the RJ45 connector) provide a great tool for basic maintenance tasks and help engineers analyze problems in the field. The LEDs not only indicate current system and network status, but also help field engineers monitor the status of attached serial devices.
Adjustable Termination and Pull High/Low Resistors
When using termination resistors to prevent serial signal reflection, it is important to set the pull high/low resistors correctly so that the electrical signal is not corrupted. Since no set of resistor values is universally compatible for all environments, the NPort® 5650-8/16 has DIP switches on the bottom panel for setting the termination and pull high/low resistor values.
LAN | |
Ethernet | 10/100 Mbps, RJ45, Auto MDI/MDIX |
Protection | Built-in 1.5 KV magnetic isolation |
Serial | |
Interface | RS-232/422/485, 8-pin RJ45 |
Signals | RS-232: TxD, RxD, RTS, CTS, DTR, DSR, GND, DCD RS-422: Tx+, Tx-, Rx+, Rx-, GND RS-485 (2-wire): Data+, Data-, GND RS-485 (4-wire): Tx+, Tx-, Rx+, Rx-, GND |
RS-485 Data Direction Control | Patented Automatic Data Direction Control (ADDC™) |
Serial line protection | 15 KV ESD for all signals |
Power line protection | 1 KV Burst (EFT), EN61000-4-4 0.5 KV Surge, EN61000-4-5 |
Optical Fiber | |
Distance | Multi mode: 0 to 2 km, 1310 nm (62.5/125 µm, 500 MHz*km) Single mode: 0 to 40 km, 1310 nm (9/125 µm, 3.5 PS/(nm*km) |
Min. TX Output | Multi mode: -20 dBm Single mode: 0 to 40 km, -20 dBm |
Max. TX Output | Multi mode: -14 dBm Single mode: 0 to 40 km, 0 dBm |
Sensitivity | -36 to -32 dBm (Single), -34 to -30 dBm (Multi) |
Advanced Built-in Features | |
HMI | LCM display with four push buttons |
Buzzer | Yes |
Real-Time Clock | Yes |
Watch Dog Timer | Yes |
Serial Communication Parameters | |
Parity | None, Even, Odd, Space, Mark |
Data bits | 5, 6, 7, 8 |
Stop bit | 1, 1.5, 2 |
Flow control | RTS/CTS, DTR/DSR (NPort 5610 only), XON/XOFF |
Speed | 50 bps to 921.6 Kbps Software Features |
Protocols | ICMP, IP, TCP, UDP, DHCP, BootP, Telnet, DNS, SNMP, HTTP, SMTP, SNTP, PPP, SLIP, RTelnet, RFC2217 |
Utilities | NPort Administration Suite for Windows 95/98/ME/NT/2000/XP/2003 |
OS Driver Support | Windows 95/98/ME/NT/2000/XP/2003/XP x64/2003 x64 COM driver, Linux Real TTY driver, SCO Unix, SCO OpenServer 5, UnixWare 7, UnixWare 2.1.x, SVR4.2/QNX |
Configuration | Web/Telnet console, or Windows utility |
Power Requirements | |
Power Input | 100 to 240 VAC, 47 to 63 Hz |
Power Consumption | NPort 5650-8/16: 158 mA @ 100 VAC, 102 mA @ 240 VAC NPort 5650-S-SC-8/16: 164 mA @ 100 VAC, 110 mA @ 240 VAC Port 5650-M-SC-8/16: 174 mA @ 100 VAC, 113 mA @ 240 VAC |
Mechanical | |
Material | SECC sheet metal (1 mm) |
Environmental | |
Operating Temperature | 0 to 55°C (32 to 131°F), 5 to 95% RH |
Storage Temperature | -20 to 75°C (-4 to 167°F), 5 to 95% RH |
Regulatory Approvals | |
EMC | CE: EN55022 Class A/EN 55024 IEC 61000-4-12 (for NPort 5610-16, NPort 5610-8-48) FCC: FCC Part 15 Subpart B Class A |
Safety | UL: UL60950-1, TÜV: EN60950-1 |
Ordering Information | |
NPort 5650-8 | 8-port RS-232/422/485 rackmount device server with RJ45 connectors and 100-240 VAC power input |
NPort 5650-8-M-SC | 8-port RS-232/422/485 rackmount device server with multi-mode fiber (SC connector) |
NPort 5650-8-S-SC | 8-port RS-232/422/485 rackmount device server with single-mode fiber (SC connector) |
NPort 5650-8-T | 8-port RS-232/422/485 rackmount device server with RJ45 connectors and 100-240 VAC power input, -40 to 75°C operating temperature |
NPort 5650-8-HV-T | 8-port RS-232/422/485 to rackmount device server with RJ45 connectors and 88 to 300 VDC power input, -40 to 85°C operating temperature |
NPort 5650-16 | 16-port RS-232/422/485 rackmount device server with RJ45 connectors and 100-240 VAC power input |
NPort 5650-16-M-SC | 16-port RS-232/422/485 rackmount device server with multi-mode fiber (SC connector) |
NPort 5650-16-S-SC | 16-port RS-232/422/485 rackmount device server with single-mode fiber (SC connector) |
NPort 5650-16-T | 16-port RS-232/422/485 rackmount device server with RJ45 connectors and 100-240 VAC power input, -40 to 75°C operating temperature |
NPort 5650-16-HV-T | 16-port RS-232/422/485 to rackmount device server with RJ45 connectors and 88 to 300 VDC power input, -40 to 85°C operating temperature |
Above items include: |
|
Optional Accessories | |
CBL-RJ45M9-150 | RJ45 (8-pin) to male DB9 cable, 150 cm |
CBL-RJ45F9-150 | RJ45 (8-pin) to female DB9 cable, 150 cm |
CBL-RJ45M25-150 | RJ45 (8-pin) to male DB25 cable, 150 cm |
CBL-RJ45F25-150 | RJ45 (8-pin) to female DB25 cable, 150 cm |
Kunden, die diesen Artikel gesehen haben, sahen auch